• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window can be a source of frustration. It could also be a chance to upgrade your glass to energy efficient or insulated windows and reap benefits like more comfort, higher resale value and reduced utility costs.

You can do it yourself at less than what it would cost to hire an expert. It requires the right tools and an hour or two of your time.

Glass

Replace your old single-paned windows seal replacement with tempered or insulation glass to improve energy efficiency, cut down on noise, and maintain the original character of your older home. The replacement window locks window panes (www.annunciogratis.net) of the window pane is easy and can be accomplished by most homeowners who possess basic hand tools. You will also need an extra window pane, glazier's tips pliers, and latex glazing putty. If necessary, you can use a heating gun to warm the old putty. Before starting, wear protective gloves and goggles since working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. This can be done with pliers, however, a flathead screwdriver can also be used in the pinch. Then, use a wooden chisel, or putty knife, to remove the remaining old putty from the frame and the sash. Be careful not to break the window sash. Work slowly and carefully. This should be done on an elevated ladder, not on the ground. Also, ensure that someone lower to keep it in place.

Once you have removed all of the old putty, it is time to prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of the width and height. These measurements can be sent to an hardware or home centers store to get cut a piece of glass that is in stock to the correct size. Alternately, you can cut the glass yourself, if you have the right tools.

After installing the glass After installing the glass window replacement near me, apply some caulking on the edges. This will make the glass weatherproof. Then, place a glazier's tip on the frame's opposite side to secure the pane into its place. The points should not be too tight that they create friction between the frame and the sash however they should not be loose.

Before applying the putty to the surface, you must knead it thoroughly until it is soft and free of lumps. Make it into pencil-sized strips. Apply the first strip to the corner of the frame, working from one corner to the next to ensure it is smooth and even.

Glazier's Points

The glazier's points are the small triangular pieces which help to secure glass into a window frame without scratching or damaging the fragile surface. It's easy to understand how to use this nefarious tool, and you'll be able to save money on the expense of an expert installation.

Once the old putty and the glazier's point are gone, thoroughly clean the frame with a utility knife to get rid of any remaining traces. If needed it is necessary to lightly sand the wood in the grooves of the rabbets to smooth rough areas. If you decide to sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Note down the dimensions of the frame. These measurements can be brought to the hardware or home center store, and the new pane will be cut a bit smaller. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane in the frame and push it into place firmly by using your hands. Then use the point of your chisel or back end of the putty knife to pierce the glazier's points as shown in Figure 11. The glazier's points should be aligned with the top edge of your pane and the shoulders should be just below that lip.

Apply a small amount of glazing compound on the edges of the glass that has been made and into the rabbet grooves to seal and protect them. Allow this to dry and cure fully.

Once the glazing compound has dried it's time to put in the new window sash. First, coat the wood with a thick layer of linseed. This will stop the new putty from drying out and cracking when it absorbs moisture. Apply this coat using a brush or the tip of your putty knife, and then use the chisel, or the back end from the putty knife to gently hammer the new sash and glazier's point into the grooves of the rabbet. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A baseball that is thrown, an errant rock or a fallen branch can cause a window to break or crack. Luckily, most windows can be repaired by simply putting a brand new piece in the right place. The glass is held in place by a small metal clip called a glazier's point, and putty, which is often called glazing compound. Remove the old pane and clean the area using an abrasive, pull-type scraper, or a wood chisel. Wear protective glasses and gloves while working. You'll need a heat gun if the window is glued to the frame.

If you plan to reinstall the original sash, gently remove the molding pieces that hold the old pane in place. Then, sand the sash to make sure it's flat and ready to be re-caulked. Once the sash is put back in place it is possible to apply a silicone caulk over the glass. This will ensure that it doesn't leak over time or discolor.

Take out the glazing points in the rabbets. These are the grooves in the sash, where the glass is. If they're difficult to work out, try placing the hand tool, such as a heat gun over them to soften them first. If you're using a heating gun, be careful not to cause damage to the railings of the sash or the sash itself by placing the tool too closely.

After the old glaze points and putty have been removed, prepare a bed for the new pane. Roll a piece of glazing compound between your hands, forming it to be about 1/2-inch thick. Press it into the rabbets, where the glass will be placed. It's important that the glass rests against the putty on both sides If you have to, lightly tap the glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glue or silicone caulk prior to pressing it into the sash. If the crack is not sealed, you will need to apply putty to keep water from getting in. After the putty is dry then clean the oily film off the glass using the help of a rag. Allow it to dry completely prior to painting. If you paint before the putty has completely dry, it will not form a strong seal and may leak or discolor over time.

Paint

You may be concerned about replacing a broken piece of glass. The truth is, replacing a single pane glass doesn't have to be costly when you do it on your own. Even a double glazing window replacement-paned window can be replaced for a fraction of the price it would cost a professional.

If you are working with large glass windows first, ensure that it is securely fixed to the frame. With the right tools and techniques, you can make this task relatively easy and fast.

When you are ready to start, remove the old window pane. Take out the glazing points made of metal that are attached to it. These are tiny triangles of metal which act as "nails" that hold the window in place. They are buried beneath a bead or glazing putty that sets to form an unbreakable wedge that holds the frame in place and conceals the edges.

Once you have the old pane removed Clean up the frame and wood. Scrape off any paint and sand down the rabbet grooves, where the glazing points were. These should be sanded down to the point of being bare, to allow you to paint them the same color as the rest the frame. After sanding, apply a layer of flax oil to the bare wood to extend the life of the frame.

Then, take measurements of the dimensions of the window opening. You'll need to determine the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass during seasons of changes. You can take these measurements to a hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.