• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

The ability of your cat to come and go from the house at their own pace is a good idea to keep it mentally and physically active. Having a flap can also aid in reducing toilet accidents by making it easier for your cat to leave the house whenever it wants to.

Measure the Door

A cat flap allows your pet to come and go whenever they want without you having to open the door. This is ideal to keep them in the house the home when you're away and helps to keep unwanted pests out of your house as well!

It is essential to take measurements of the door to ensure you get the right size cat flap. There are many sizes available. This will ensure that you purchase the right size to fit inside your door made of upvc, otherwise, it could be too small or too large for your cat and he will be unable to use it.

Before you take any action, though, take a ruler and take measurements of the width of the door in several places along its edges. You should also determine the height of the door in a few places. A door that is too tall will cause your cat to do an exercise routine every time it uses the flap.

Ask a glazier for help when you're unsure of what to measure for the door. They can determine if your door is suitable for cat flaps and help you decide on the size of flap to buy.

Mark out the shape of the hole on the door once you have your measurements. This will aid you when cutting the hole, and will save you money!

It is also important to ensure that the hole you're making is in the right place. For instance, if fitting the cat flap in a patio door, you must ensure that the hole isn't too close to any hinges, as this can cause leakage and damage to the seal.

If you have a glass door you could want to let this job to a glazier. It can be difficult to install a cat-flap within an existing pane. You might also discover that it cracks and loses its weatherproof seal.

Measure the cat flap in upvc door panel

A cat flap lets your pet move around as they wish without having to leave him home on his own. It can also stop the draughts from entering your house, which aren't good for you or your cat!

If you do have a uPVC or composite back door with cat flap fitted, it could be a challenge to put in a cat flap. These doors are made of different materials, and the way they are installed is different. Before you think about installing an egress flap to your uPVC or composite door, make sure that it is compatible and you have checked with the manufacturer because alterations could cause the warranty to be invalidated.

In general, these kinds of doors are designed to be tough and durable and have insulation built-in. This makes them more resistant to elements of the weather than other types of doors, however they can be a challenge to insert the cat flap. If you're uncertain about whether your uPVC or composite door is able to accommodate a cat flap, consult with a professional joiner prior to beginning.

To ensure that your cat can pass through the door, you'll have to measure their height. This is easiest when they're asleep or calm so that they're not moving around too much. Once you have their height and weight, you can determine the distance from their stomach to the floor in order to determine the position of the flap's bottom. This position can be outlined on the door.

If your uPVC or composite door is made of metal (either steel or aluminium) it is important to be extremely cautious when cutting it using power tools. Cutting into metal can cause it crack, especially when the area is made of toughened glass. It is highly recommended to hire an experienced glass installer to install an e-cat flap on the pane. This will stop the glass from breaking and becoming hard. A glazier will also be capable of providing you with a circular cat flap that is less likely to break and safer for your cat to use.

Cut the Hole

If it does not, you can make one yourself by using a piece of thin paper (tracing paper is the best choice). If it doesn't, you can make your own with a thin piece of paper (tracing papers are great). Once the shape has been pencilled in on the door you can then use your spirit level to ensure that the shape is horizontal. This will allow your cat's flap to properly fit into the opening and stop it from being in a position to slide open or close.

Then, you can use your jigsaw and cut the shape that has been written on the door. Make sure that you're using a blade that is suitable for use on uPVC doors - usually it will be marked accordingly however, if not, ask the staff at the DIY store for guidance. After the hole has been cut and the flap is placed against it and then open it to make sure the flap moves smoothly. If it becomes stuck at any point, you can use the filer or the rasp to fix this.

Verify that there aren't gas or electric pipes inside the door you're planning to cut through. Your jigsaw could cause damage to them. Similarly you should be aware of any handles or other door fixtures that need to be removed to install the cat flap. You should be careful not to harm them during the process.

The majority of people who install a cat flap on their own will have an ordinary solid uPVC door, and therefore will not be dealing with any of these problems. However, if your door is constructed of timber or has decorative panels that cannot be removed, this could make it more difficult to complete the task.

For these types of jobs, it is recommended to seek out expert guidance from a cat-flap fitting a cat flap in a upvc door (www.pdc.Edu) expert. It is essential to do them correctly to avoid any future issues. It is essential to do it right because doing it wrong can damage the door and void the warranty.

Install the Flap

After you've made your hole cut, put the flap in place to test whether it will fit and opens easily. If you find any points that stick or catch, use a hand file or sandpaper, to file them down until they fit perfectly and can be opened without issue. Make sure the flap is in line with the door.

Some kits include an example of this, however, if it doesn't provide a template, you could use a piece or thin paper instead, something similar to tracing paper. Place the paper against the door and draw a line where you will need to place the flap (this will serve as your cutting guide). Then, using the pencil lines you've made on the door, mark four screw holes in the corners of the flap. These will be the screw points that you'll use to secure the flap into the right position.

The majority of uPVC doors are solid and therefore simple to cut into. If your door is constructed of GRP or composite however, it could be more difficult. If you're not experienced in this area, it might be beneficial to engage an expert to complete the work for you. They will also be able to inform you if the door is suitable for the installation of the cat flap.

It is possible to install the cat flap onto composite doors. However, it's essential to verify with the manufacturer or a professional joiner before you do so because any changes to these doors could invalidate the warranty. If you choose to carry out the work yourself, remember that this could be messy and dangerous job.

You'll need a saw or grinder to cut through composite doors, rather than just the GRP. Be aware that this can be very dangerous and you'll need to take great care not to harm the door or yourself, as it is extremely fragile. It's also important to note that cutting holes into any type of glass for a door is much more difficult than making the same change in a uPVC or solid timber door.