• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

If the locks on your door begin to begin to show signs of wear and tear, it's generally a good idea to replace patio door lock them. This could be due to things like having trouble turning the lock or finding a key that doesn't fit.

The good news is that installing new hardware for your door locks is actually very easy. All you have to do is follow these steps.

Deadbolt

The deadbolt is your primary security for your door against forced entry. It is stronger and safer than the latch that activates the lock. So, you'll want to make sure that the new deadbolt you purchase meets your requirements. If you can, select a deadbolt made of case-hardened steel that doesn't have exposed screwheads on the exterior to stop drilling by anyone else. To ensure security, the interior side of the deadbolt should be mortised into the door frame.

When you install the deadbolt, check that your new deadbolt's bolt is extending smoothly into the strike plate when you shut and lock the door. If it isn't then use a chisel made of wood to make a mortise for the bolt hole into the strike plate and then re-install the deadbolt. When you close and lock your door, ensure that the latch of the doorknob meets the hole of the deadbolt.

Check that the new deadbolt matches the old one prior to installing it. The majority of door locks come with a design that tells you how high over the doorknob the bolt should be, but it is always recommended to speak with an expert at a hardware store if you're not sure of the backset measurement that is appropriate for your patio doors locks replacement. They should be able to point you in the direction of models that are compatible with your patio doors locks replacement and existing deadbolt opening.

After you've confirmed that your new bolt assembly is the correct length, insert it into the hole in the door. Screw the latch faceplate in place if your new deadbolt is equipped with one. It is a good idea to attach the latch faceplate to the frame with the recommended screws, and also.

Some lock sets include a "dummy" or decorative bolt that allows you to install the keyed deadbolt and still have a functioning latch. If you have this option the dummy bolt must be installed with the same screws as the faceplate for your latch, and it's important that the two fit together properly for maximum security.

Some deadbolts are accessible only by thumb-turn from the inside some have two cylinders that allow both keyed and unkeyed access. Whatever type you select it's a good idea to buy a commercial-grade lock to ensure the highest security. They are usually tested to last for 250,000 cycles of opening and closing before being sold to homeowners.

Latch

The latch is the part that retracts the bolt when you shut or open the door. It's usually secured by screws on the side of the lock, however it could also be fixed to the strike plate or to the inside of the door jamb. It is crucial to replace a door lock with the correct one that matches the hardware you have. You can verify this by putting the latch next to the hardware you have already, or you can look on the label of the replacement. Dunn Lumber carries a variety of brands, however it's best to stick with the same brand as your existing hardware to ensure that you receive a latch that will fit properly.

Some doors are equipped with a hasp instead of the latch. A hasp is straps with slots punched into it that fits over the staple. The staple is then fixed to the door frame or door by nail. When the door is closed and the strap is pulled, it will pull the staple down and secures it in place. A hasp is usually used in commercial structures because it's cheaper than a deadbolt.

Like any mechanism that has moving parts, locks can wear out from repeated use over time. Sometimes, the internal mechanism could "stick" or become difficult to turn. This will require the upvc replacement door locks of the entire lockset. Sometimes, the exterior doorknob can fail and it is essential to replace it too.

If your lock is stuck, put some graphite in the keyhole. You can either squirt some on the key or sprinkle it on the inside of the lock, then operate the lock a few times to incorporate the graphite into the mechanism. You can remove the knob using an screwdriver, which will expose all the parts and let you see what is going on inside.

After removing the knobs, tighten the two or three setscrews on the edge of the cylinder by turning them clockwise. The faceplate must be removed and replaced. Surface-mounted rimlocks have an additional set of cylinder setscrews on the back case which must be removed, as well as the faceplate.

Strike Plate

The strike plate, attached to the door frame, above the holes that accommodate the deadbolt or master key bolt system, strengthens and upgrades a locking mechanism. It keeps intruders out by making sure that the latch of the lock is secured in the strike plate when the latch or bolt is engaged. In addition to enhancing security, a high-quality strike plate can also enhance the durability of locks.

Standard strike plates are flat metal plates with holes, or a series of holes, cut into them. It is affixed to the door frame typically using screws, which gives the latch something to sink into when it closes. It is crucial that the strike plate is precisely aligned with the lockset to offer maximum protection against burglaries.

If the strike plate on the door is damaged you should replace it as soon as possible. This will ensure that your door can close and latch properly. To replace a strikeplate you must first make sure that it is properly aligned with the bolt hole in the doorjamb. This can be done easily by placing a piece adhesive tape over the bolt hole and then testing the latch. If the latch doesn't catch then take off the tape. Then, chisel the hole to make the strike plate aligned with the doorjamb.

After the area has been chiseled it is essential to use a stronger bolt to anchor the strike plate. They must be at least 3 inches long in order to ensure they are securely fixed to a stud that is behind the trim board. If you do not install the longer screws, then the doorjamb's wood could split during a kicking attack by an burglar, making the door vulnerable.

A professional locksmith can quickly replace door lock a strike plate that's been damaged or worn. They can also put a new strike plate on the door that hasn't had one before. Additionally, they can upgrade existing strike plates to increase the security of a property and improve its appearance. This could aid property owners in attracting tenants who are looking for a safer living space and peace of mind.

Keys

The key cylinder is a part of your lock that accepts a particular key to shift pins into place so that the inner handle can be turned. The key cylinder is the primary part of your door lock, as it performs the purpose for which locks were designed to protect you, your family members, and your belongings. It is for this reason that people frequently have their locks rekeyed instead of replacing them.

It is more difficult to replace a lock than to simply switch out the existing handle and deadbolt. The old hardware, cylinder and handle (if you have the knob and lock combo) must be removed from the door before the new lock can be installed. There are many DIY-friendly kits that can be used to replace the door lock. However, it's best to contact an expert locksmith to ensure that the job is done correctly.

Before you can install an entirely new lock and cylinder, it is important to have the right key for your home. A key that is duplicate will not work properly and could even cause the lock to fail completely, rendering it impossible to open. A trained professional can help you avoid this by ensuring that you have a genuine, door lock replacement functional key for your home.

The next step is to take off the faceplate, then the latch plate. To remove the screws that hold them in place, you will require an screwdriver. If the new plates will be identical to the original ones, you may want to secure them to speed up the process. If you need to replace them, make sure not to overtighten the screws because doing so can affect their grip on the door.

After removing the plates, you'll need to measure for the new lock. While many contemporary locksets will fit on a standard thickness of door, it's best to know the dimensions of your door prior to installation to avoid frustration when you arrive at the hardware store. Doorknob locksets tend to be different sizes from deadbolt locks commercial models might come with a larger latch or bolt.