• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace upvc door lock to Replace Door Locks

The first protection is your door lock. It will stop unauthorized access to your home. The locks may require replacement because of signs of wear and tear or other circumstances such as moving into a new residence or a break-in.

To begin, determine the size of your cylinder using the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will assist you purchase the right-sized lock.

Deadbolt

If you want to ensure your door is safe from intruders, it's a good idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it harder for an intruder through the door. A single-cylinder deadbolt can be activated using a key on the exterior and a thumb-turn piece situated inside. A deadbolt is only effective only if it's correctly installed, though.

First, you must determine whether the door already has an existing hole for a deadbolt, or if you'll need to bore it out. Using the template that comes with your lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, you can use your tape measure to determine how high the deadbolt should be. Mark this height on the door edge, and then use a speedsquare to draw a straight line across the mark you made for the bolthole.

Then, using a power drill, bore through the hole until it reaches the opposite side of the door. It may take a while. Sand the hole and the door edge to make it smooth. At this moment, it's a good idea also to stain or Replace Door Lock paint your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assemblies of the deadbolt, as well as the internal bolt. Then, remove the bolt and replace door lock it with a brand new bolt that matches the door hardware. The bolt is usually attached to a set plate which you'll need to unscrew. After this, you'll need to chisel the door frame to accommodate the strike plate.

If your strike plate is out of alignment, it could be because the previous installer failed to mortise it properly or that a weatherstripping has changed the strike's location. You'll need to re-mortise your strike plate and possibly even the deadbolt itself to fix the issue. Once you have completed this check the deadbolt by closing and locking it. Be sure the bolt extends into the strike plate, and then test the key to make sure it closes and opens effortlessly.

Knob

When a door knob is worn out, it can make your business or home less secure. It can also make opening and closing the door more difficult, which is why it is an ideal idea to replace the knob. replacing door locks knobs is an simple DIY project that shouldn't take more than 30 minutes to complete. Make use of pliers or a screwdriver to remove any knobs or handles. Be cautious not to scratch other parts of the door.

Before starting, you'll want to spray WD-40 or some other dry lubricant on the mechanism of the door knob. This will assist the new lock to slide smoothly when you turn it. It's important to use a quality knob and handle that is compatible with your doors currently in order to ensure that the lock is operating properly. If you don't already have a doorknob that is compatible and handle, you'll need to purchase a replacement.

To begin the replacement door locks process, look over the knob or handle to determine what screws hold it in place. If there are no screws to hold it in place, you can use a screwdriver to secure the cover plate in between the screws plate hidden behind it.

After you have removed the knob, inspect it for indications of damage and rust. If the knob has any marks or scratches it's time clean it. Otherwise, it shouldn't require any major work.

It's time to install the new knob. Before you do that, look over the new knobs to ensure that you're choosing the right one for your door. You'll need to pick one with an extended rod that locks with the rod mechanism of the other knob. After you've placed the new knob in the hole and then put it in the latch.

Thread the latch plate screws down and then test the spring by pushing down on it several times. The latch should rise every time. Next, install the other new knob and connect it with the rod mechanism on the first knob. Thread the long screws of the interior doorknob through the holes for the cylinder on the exterior knob, and fix it in the knob's position.

Latch

A latch is a piece of metal that extends through the doorjamb to secure it shut. The latch can be operated by a knob or handle on the inside of the door, or a thumb-turn on the outside. The latch can be secured with deadbolts to prevent intruders from breaking in through the door's glass. It can also guard against the accidental or deliberate closing by children or animals. The latch can be fitted with single cylinder deadbolts or a double cylinder deadbolt, according to the security level you prefer.

Installing a deadbolt is the same as installing a latch, however, there are some distinctions. First, measure the setback of the doorjamb with a tape measure to make sure the new lock will fit. The setback is measured from the edge of doorjamb up cost to replace upvc door lock mechanism the center of hole for the latch plate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If your setback is higher it is possible to purchase a latch that is larger from a locksmith or hardware store.

Next, drill a hole for the latch plate at the edge of the doorjamb. Use a chisel and cut the mortise of the latch. Make sure that the depth is sufficient for the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure that it's positioned correctly.

If the strike is positioned too high, the door can be kicked in or pressure applied to it using a crowbar, or tire iron. This could cause the doorjamb to crack. To remedy this issue, the strike can be lowered by drilling a new hole into the doorjamb and chiseling out the core of the old hole.

The final step is to install the new strike plate, which can be accomplished by screwing it in place over the existing screw holes. Then you can use wood putty to fill in the old screw holes and the bolt hole that will not be used. After the putty is dry you can sand it until it has a smooth finish.

Strike

An electric strike is the metallic piece where the deadbolt and latch are engaged when the door is closed. It is an essential part of the lock's overall safety because it prevents the door from opening, and also provides additional resistance to force or kicking. If a door is equipped with an electric strike, it can be opened using an entry key or the control unit that controls the electrical impulses.

Traditionally the installation of an electric strike required cutting out a portion of the doorjamb to release the latchbolt of a circular lock from the pocket in the strike. This is a drawback in regards to the aesthetics of an opening as well as exposing the latchbolt and keeper mechanism to any unauthorised users.

Recently, a number of electric strike makers have come up with a new type of electric strike dubbed the "No Cut" strike that doesn't require cutouts in the doorjamb for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp which lifts the latchbolt and keeper when it receives a signal from a reader. The latchbolt and keeper are lifted higher on the ramp thanks to the retract. When the door is closed the deadbolt remains retracted, and the latchbolt retracts in the keeper.

Installing an electric strike can be a simple process, especially if you are replacing the strike on a previous door. If you're upgrading an access control system to an electric strike, it is important to ensure that the new system is compatible. You will also have to ensure that the strike is properly connected to your access-control system and set up to function in a safe manner.

One way to protect against access by unauthorized persons is to upgrade the strike on your doors to a heavy-duty strike plate. The plates are made of up to six screws of three inches instead of two screws of three-fourths of an inch. These screws are longer, making it harder for anyone to break the frame and reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.